Mounting A Tub
Mounting A Tub
Blog Article
This article below in relation to How to Install a Bathtub Yourself is pretty much enjoyable. You should read it.
Mounting a tub isn't specifically rocket science, however it does require solid plumbing, woodworking, and occasionally, tiling skills. Changing an old bathtub with a new one is additionally a moderately tough project. If the old tub is conveniently available, the task can move immediately; if you need to open a wall surface to get rid of the old tub as well as place the new tub, the job is much harder. In either situation, the task is within a home handyman's skills, although you will certainly require an assistant to move out the old bathtub and also set in the new one. Make certain you have qualified on your own for the work and are comfortable trying it. As opposed to hiring a specialist to take control of a halfway-completed project, it is much better to think about using one before you begin. Possibilities are you might require a professional plumber to make tube connections.
This post will certainly aid you install a new tub in your shower room if you have actually already bought a new tub as well as do not require to change the arrangement of your previous supply of water pipes.
Your tools as well as material checklist ought to comprise the following:
Removing Old Touches
If you require to replace old taps with brand-new ones as a part of your installment, after that the first thing you need to do is separate the water supply. After doing so, switch on the faucets to drain pipes any water staying in the system. The procedure of eliminating the existing faucets can be fairly bothersome due to the restricted gain access to that is commonly the instance.
Make use of a basin wrench (crowsfoot spanner) or a tap device to reverse the nut that attaches the supply pipelines to the faucets. Have a towel ready for the remaining water that will come from the pipes. Once the supply pipes have been eliminated, utilize the exact same tool to loosen up the nut that holds the faucets onto the bath/basin. You will certainly require to quit the solitary faucets from transforming throughout this procedure. As soon as the taps have been eliminated, the holes in the bath/basin will have to be cleaned up of any type of old securing compound.
Before carrying on to fit the brand-new taps, compare the pipe connections on the old taps to the brand-new faucets. If the old faucets are longer than the brand-new faucets, after that a shank adapter is needed for the brand-new faucets to fit.
Suitable New Taps
If the tails of the new taps are plastic, then you will need a plastic connector to prevent damage to the thread. One end of the connector fits on the plastic tail of the tap and the other end gives a link to the current supply pipelines.
If you need to fit a monobloc, then you will call for lowering couplers, which links the 10mm pipe of the monobloc to the conventional 15mm supply pipe.
Next off, place the faucet in the mounting hole in the bath/basin making certain that the washing machines are in place in between the faucet as well as the sink. Secure the faucet in position with the producer given backnut. When the tap is securely in position, the supply pipes can be connected to the tails of the faucets. The faucets can either be connected by utilizing corrugated copper piping or with typical tap adapters. The previous type needs to be attached to the tap finishes initially, tightening just by hand. The supply pipelines can later be attached to the other end. Tighten both ends with a spanner after both ends have actually been connected.
Mounting the Tub
Using both wooden boards under its feet, place the tub in the required placement. The wooden boards are handy in uniformly spreading out the weight of the bathtub over the location of the boards instead of concentrating all the weight onto four little factors.
The next objective is to ensure that the tub is leveled all round. This can be achieved by inspecting the level and readjusting the feet on the bathtub up until the level reads level.
To mount taps, fit the bottom of the outermost flexible faucet adapter to the suitable supply pipeline by making a compression sign up with; then do the exact same for the various other tap.
Turn on the water and inspect all joints and also new pipework for leaks as well as tighten them if essential. Fill the tub as well as additionally check the overflow outlet and also the normal outlet for leakages.
Ultimately, fix the bath paneling as explained in the supplier's instruction manual. Tiling and securing around the bathtub must wait till the bath tub has been used a minimum of when as this will certainly settle it into its final setting.
Planning for the Installment
Firstly, the sustaining structure provided with the bathroom needs to be fitted (if called for) according to the manufacturer's directions. Next, fit the taps or mixer to the bathtub. When suitable the faucet block, it is important to ensure that if the tap includes a plastic washing machine, it is fitted in between the bathroom and also the taps. On a plastic bath, it is also sensible to fit a supporting plate under the taps system to avoid stress on the tub.
Fit the adaptable tap ports to the bottom of the two taps using 2 nuts and olives (occasionally provided with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet hole, and then pass the outlet through the hole in the bathroom. Make use of the nut provided by the producer to fit the plug-hole. Analyze the plug-hole outlet for an inlet on the side for the overflow pipe.
Next, fit the end of the flexible overflow pipeline to the overflow electrical outlet. After that, screw the pipe to the overflow face which should be fitted inside the bathroom. Make certain you utilize all of the supplied washing machines.
Attach the trap to the bottom of the waste outlet on the bath tub by winding the string of the waste outlet with silicone mastic or PTFE tape, and screw on the catch to the electrical outlet. Link the bottom of the overflow tube in a comparable manner.The bathroom should currently be ready to be suited its last setting.
Tiling Around the Bathtub
In the location where the bathroom meets the floor tile, it is needed to seal the joins with a silicone rubber caulking. This is necessary as the fitting can move sufficient to break a rigid seal, creating the water to permeate the wall in between the bath and also the tiling, causing complications with wetness as well as possible leakages to the ceiling below.
You can pick from a selection of coloured sealers to blend in your components and installations. They are offered in tubes and also cartridges, as well as are capable of securing gaps approximately a width of 3mm (1/8 inch). If you have a bigger gap to load, you can fill it with spins of soaked paper or soft rope. Keep in mind to constantly fill up the bath tub with water before securing, to enable the activity experienced when the tub remains in use. The sealer can break rather early if you do not think about this movement prior to sealing.
Additionally, ceramic coving or quadrant tiles can be utilized to border the bath or shower tray. Plastic strips of coving, which are easy to use and also cut to dimension, are also quickly readily available on the market. It is suggested to fit the tiles utilizing waterproof or water resistant glue and grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
Do you really like reading up on Installing A Bathtub? Give a comment below. We'd be delighted to know your opinions about this entry. We hope to see you back again in the future. Remember to take the opportunity to share this blog posting if you enjoyed it. Thanks a bunch for your time. Kindly visit our blog back soon.
Top Article
Report this page